LED Strip Mounting Tape

Double Sticky Tape Company is a manufacturer of LED Strip Mounting Tape for narrow LED strip lights, aluminum channel assembly, and back adhesive replacement. This narrow double sided tape for LED strips is slit to 5-12 mm widths with typical +/-0.2 mm tolerance, helping lighting assemblers match PCB width, reduce adhesive overflow, and keep the strip flat after 24-72 h dwell. PET, foam, and thermal adhesive carrier options are available for indoor and covered outdoor lighting assemblies.

Product Video

Product Photos

Product Overview

LED Strip Mounting Tape is made for small lighting assemblies where a few millimeters can decide whether the installation looks clean or starts lifting at the edge. A 5 mm or 6 mm tape is often used for slim LED strip lights, while 8 mm, 10 mm, and 12 mm widths are selected for wider PCB strips and aluminum channel grooves. If the tape is wider than the strip body, exposed adhesive can collect dust along the edge. If it is too thick, the strip may sit too high and affect diffuser fitting or light consistency.

For low-profile installation, PET film grades around 0.05-0.2 mm help keep the strip flat inside the aluminum profile. Thin foam or thermal adhesive grades around 0.3-0.8 mm can be selected when the surface has slight unevenness or when closer heat contact is needed between the LED strip and aluminum base. This low profile LED strip adhesive tape is also useful when the original backing loses tack after storage, repeated handling, heat exposure, or surface contamination.

Before batch use, this double sided tape for LED strip lights should be checked on the actual aluminum, PC, or ABS surface. Molded plastic texture, coating, release-agent residue, and cleaning method can change final peel strength. Surface preparation matters: dust, oil, fingerprints, aluminum cutting debris, silicone residue, and plastic release traces can all reduce adhesive wet-out and create local peeling points.

Benefits

• Narrow 5-12 mm roll slitting matches common LED strip PCB widths without exposed adhesive edges.
• Typical +/-0.2 mm width tolerance helps the tape fit aluminum channels and narrow lighting grooves more consistently.
• Low-profile PET construction keeps LED strips flat and reduces diffuser interference.
• Heat-resistant adhesive supports normal LED working conditions, with typical grades rated around 80-120 C depending on carrier and adhesive system.
• Stable liner release supports hand application and semi-automatic processing without tearing or uneven peel.
• LED strip back adhesive replacement tape helps reduce strip-end peeling, corner lift, solder-pad lifting, and wire-exit stress before batch assembly.

When should low-profile LED strip mounting tape be selected for aluminum channel assembly?

Low-profile LED strip mounting tape is a better choice when LED strip lights need to sit flat inside a narrow aluminum channel. A thick foam tape can raise the strip, make the diffuser harder to close, or create uneven light output along the channel. Thin PET or thermal adhesive carrier grades work better as aluminum channel mounting tape because they keep the strip close to the aluminum base while maintaining a neat profile. For cabinet lighting, display lighting, shelf lighting, and covered outdoor linear lighting, the tape width should match the strip body, commonly 5 mm, 8 mm, 10 mm, or 12 mm. After application, a 72-hour observation helps check edge lifting near strip ends, solder pads, wire exits, and channel corners.

Product Packaging

Product Production

TDS

[wptb id="5625" not found ]

Loading Container

Applications

1. LED strip back adhesive replacement tape for weak, aged, or contaminated original backing
2. Aluminum channel mounting tape for cabinet, shelf, display, and linear lighting
3. PC and ABS lighting housings after surface cleaning and sample validation
4. Indoor LED strip lights where low height and clean alignment are required
5. Covered outdoor lighting assemblies requiring heat-resistant adhesive stability
6. Narrow roll processing for lighting factories, assemblers, and converters
7. LED strip installations where wire exit stress and corner lifting need to be checked before batch assembly

How should the surface be prepared before replacing weak back adhesive on LED strip lights?

Before using LED Strip Mounting Tape to replace weak back adhesive, both the LED strip back side and the mounting surface should be cleaned carefully. A quick wipe is often not enough when aluminum dust, oil, fingerprints, silicone residue, or plastic release-agent traces remain on the surface. For aluminum channel, PC surface, and ABS housing bonding, the surface should be dry, stable, and free from loose coating. After the tape is applied, firm pressure should be used along the full strip length so the adhesive contacts both sides evenly. A 72 h dwell check before full production helps confirm peel strength, heat resistance, edge lifting behavior, liner release stability, and wire exit stress.

FAQ

1. What width is commonly used for LED Strip Mounting Tape?

Common widths are 5 mm, 6 mm, 8 mm, 10 mm, and 12 mm, depending on LED strip PCB width and aluminum channel size.

2. Can this tape replace weak original LED strip backing?

Yes. This double sided tape for LED strip lights is suitable for back adhesive replacement after cleaning, firm pressure, and 24-72 h dwell.

3. Is PET or foam carrier better for aluminum channel?

PET is better for low-profile fitting. Thin foam is better when slight surface unevenness needs compensation.

4. Can it bond to PC and ABS surfaces?

Yes, but molded plastic surfaces should be tested first because texture, coating, release residue, and cleaning method affect final adhesion.